Blog Article

Capex Structuring, Capacity Utilisation and the True Landed Cost of Production

Capex Structuring, Capacity Utilisation and the True Landed Cost of Production

Quick answer: The true landed cost of production is the full cost of making one unit, including materials, freight, labour, power, financing on capex and fixed overheads spread over the units you actually produce. When capacity utilisation is low, the same fixed costs fall on fewer units, so the real cost per unit rises even if your quotation sheet never changes.

Most Indian manufacturers price from a costing sheet built when the plant was new. That sheet assumes the machine runs at the volume used in the loan application, and that the cost of the loan stays the same. Neither holds for long. This guide explains how to structure capex, measure capacity utilisation honestly, and calculate the landed cost that should drive your pricing. It is the approach our CFO consulting services team uses with manufacturing SMEs.

Why capex decisions go wrong

Capex is usually decided on three numbers: the machine price, the EMI and an expected output. The problems sit in what those numbers leave out.

  • Funding mismatch. A machine that pays back over seven years is often funded with a three-year loan or, worse, working capital limits. Repayments then compete with payroll and suppliers for the same cash.

  • Optimistic volume. The project report assumes 80–85% utilisation from year one. Real plants often take 18–24 months to ramp up.

  • Hidden running costs. Power, maintenance contracts, tooling, insurance and operator training rarely make it into the payback calculation.

A good capex structure matches the funding tenure to the asset's useful life, keeps a buffer for the ramp-up period, and is stress-tested at 50% and 65% utilisation, not just the best case.

How to structure capex the CFO way

  1. Start from demand, not capacity. Size the investment to confirmed or highly probable orders for the next 24 months.

  2. Match tenure to life. Use term loans or equipment finance for long-life assets, and keep working capital limits for working capital.

  3. Phase the spend. Buy in modules where possible so capacity grows with orders.

  4. Build the downside case. Check whether you can service the debt at 50% utilisation. If not, renegotiate tenure or a moratorium before signing.

  5. Track the post-investment review. Compare actual output, cost and cash against the project report every quarter for the first two years.

If you are negotiating a machinery loan right now, check the moratorium, covenants and prepayment clauses against your ramp-up plan before you sign.

Capacity utilisation: the number that changes every cost

Capacity utilisation is actual output divided by practical capacity, which is the output you can achieve after planned maintenance and changeovers. Theoretical capacity flatters you; practical capacity is the honest benchmark.

Here is a simple example of the same plant at different levels of utilisation:

Utilisation

Units per month

Fixed cost per month (₹)

Fixed cost per unit (₹)

85%

8,500

25,50,000

300

65%

6,500

25,50,000

392

50%

5,000

25,50,000

510

The variable cost per unit stays roughly the same, but the fixed cost per unit rises by 70% between 85% and 50% utilisation. If your price was set at 85%, every unit sold at 50% may be loss-making, even though the plant looks busy.

What goes into the true landed cost of production

Landed cost is more than the bill of materials. For each product, include:

  • Materials at landed price: purchase price plus inbound freight, insurance, customs duty and handling, net of input tax credit you can actually claim.

  • Conversion cost: direct labour, power and fuel, consumables and tooling.

  • Quality and waste: scrap, rework and rejected batches, allocated to the products that cause them.

  • Capex cost: depreciation plus interest on the capex loan, allocated on machine hours.

  • Fixed overheads: factory rent, supervision and maintenance, divided by actual output, not budgeted output.

  • Outbound logistics and terms: freight to the customer and the financing cost of the credit period you give.

When this is done properly, most manufacturers discover that two or three product lines carry the plant and a few loss-makers hide behind averages. Choosing the right costing method matters too; see our comparison of standard costing vs actual costing.

Turning landed cost into decisions

Once you know the true cost per product, three decisions become clearer:

  • Pricing: set a floor price per product at landed cost plus target margin, and stop quoting below it.

  • Product mix: push volume toward products that earn the most per machine hour, not per unit.

  • Capacity: decide whether to fill spare capacity with job work, a new customer segment, or exports before buying the next machine.

This is where specialist financial consultancy firms add value: they connect costing, capex and cash into one plan instead of three separate spreadsheets. For a broader view of the sector's growth, the India Brand Equity Foundation's manufacturing overview is a useful reference, and MSME owners can check schemes and classification rules on the Ministry of MSME website.

Try this CFO prompt

Use this prompt with your AI assistant to draft the capital allocation section of your next investor or bank presentation:

"As a CFO, draft a 400-word investor deck section on our capital allocation strategy for FY2026–27. Pillars: capacity expansion, debt reduction and working capital. Explain how capital is prioritised across each, including the utilisation level we need before approving new capex."

Review the output against your actual utilisation and landed-cost numbers before it goes to a lender.

FAQs

What is a good capacity utilisation for an Indian manufacturing SME?
Most SMEs aim for 70–85% of practical capacity. Below about 60%, fixed costs per unit usually rise enough to erode margins.

What is the difference between landed cost and cost of production? 
Cost of production covers making the product in the factory. Landed cost also includes inbound and outbound logistics, duties, financing and credit costs, so it shows the real cost of delivering each unit.

When should a manufacturer use CFO consulting services for capex?
Before signing any major capex or machinery loan. A CFO can stress-test utilisation, structure the funding and set the post-investment review.

Can a fractional CFO calculate landed cost without new software?
Yes. Most landed-cost models start in your existing ERP or Tally data and a structured spreadsheet, then move into MIS dashboards once the logic is proven.

Build your capex plan on real numbers

CFOSME helps manufacturers in Mumbai, Pune and beyond structure capex and price from true landed cost. Plants in Tamil Nadu work with our team as their financial advisor in Chennai. Unlike most business finance consulting firms, we give you a senior CFO, not a junior analyst. If you are planning an expansion, book a free consultation before you sign.

Contact Us